Roman ghost pricing in big box stores can leave a person thinking of aluminum foil, hanging sheets and plainly giving up. Even with basic sewing skills you can make your own shades and save a bunch.
These shades are designed so that they can be removed and tossed in the washing machine. . Most shadows are not. And instead of choosing the colors and textures of the shades available, you can use any fabric that you like.
Here’s what you need: A sheet of leather (1″ x 1″ wood, available at inexpensive DIY stores) cut to fit inside the top of the windows_frame, two 1″ screws to mount the strap to the top of the frame, nails, fabric and liner (if desired) cut 1″ larger than desired shade, hook and loop tape or heavy duty tape, sewing supplies or fabric glue, “plastic rings or ring tape Other supplies include tape, chalk or pins to hold the fabric together. You’ll also need 3/8” eye screws to raise and lower the shade. A press or other end can be used for the end of the cord. roman shade erect, a 3/8″ rod dowel and screen cleat.
Wood and screws are available at any DIY store, while other supplies are available online and at all sewing stores. If you don’t have a sewing machine (or a friend who does) fabric glue can be used.
Begin by measuring the inside of the engine window, top to bottom and side to side. The Roman shadow is going to fit within the frame. If the desired outside window shades is going to be, measure carefully. Add 2″ to this measurement so there will be 1″ total feed around.
Staples, using furniture or glue, cover the stripped tome with the fabric and mount it on top with the window boards ending ¼” inside each This will allow the Roman shade to be inside the windows and another curtain can be pulled over it.
The fabric jacket can be a window darkening or UV fabric purchased at the sewing center (be sure to follow the cleaning instructions for this specialty fabric), or fabric of any color that the designer chooses. You can also make a film just for this shade and save energy quickly. Before you cut any fabric, wash and dry it according to the instructions so that if it shrinks, it will be before the Roman shade, not after.
Cut the fabric and lining to measurements. Fabric with right sides facing each other. Allowing a 1″ seam allowance, sew around 4 pieces, ending 6″ from the end. Cut off the corners at the corner (don’t cut through the seam) and fold inside. Fold the last 6 inches to match the seam, press in place and sew or glue closed.
At the top of the inside of the fabric, the SUO or glue on one side of the hook and the strap or tape are broken. Fasten the other side with glue or staples to the strip. This allows the Roman shade to be removed for cleaning.
Measure on the back of your Roman shade 4″ from each side. Tape the rings to the shade pin, making sure the rings measure across as well. This allows the shade to fold evenly when lifted. Make sure the 2 circles are 1″ from the bottom of the shade. This is where the dowel rod will be inserted.
Pull off the spin ring or glue it in place. Individual rings can be used and are less expensive, but a strip is easier. If not using tape, measure across the back every 6 to 8 inches and mark the cutting lines with 4″ inside the line.
They roll in rings to the shade outside. Supported by stripped leather and a brand name ring band. Bring the mark to the bottom center of the wood and place the eye screws here. they will hold the ropes to raise and lower the Roman shade.
Now the fun part. Cut the rope 3 times the length of the shadow. Gather one end at the bottom of the ring (hair can be applied to the utility) and thread it through the circles. Both sides do this. Roll up the shade again, with the top ropes on the outside. Thread the cord left to right through each eye of the screw and leave the moment hanging. (Attaching a small piece of hook and loop or snap helps to hold it in place.) Leave the right-hand thread to the right of the screw and hanging through the right-hand eye. Place the shade across the width and allow it to develop its full length.
Lower the dowry staff through the rings in the shadow below. Tie the ropes in a knot at the top. Either leave the ends hanging or end with a head or end. Do not tie the cords in a loop, this is a danger to small children.
Remove the ropes and pull gently until the shade is lifted up. Determine where you want the cleat to be. Cleat boarded this place. There will be ropes around the cleat to hold the shade in place.
Make sure the folds are straight and leave the Roman shade for about one week to allow the fabric to fold evenly.
To clean, remove the paining stick at the bottom, loosen the ropes from the rings, and remove them from the pot at the top. Wash and dry, re-position as before.
You don’t have to spend a fortune to have Roman shades in your home. make it yours, and save it. Of course, if you have a friend who doesn’t sew, offer to buy the fabric for the shades as a sewing service.
