The “ART” of hanging and carrying out a drought is not as offensive a job as one might think. The point is that with the right tips, a person can save a lot of money by cutting labor costs.
The first thing you need to do is calculate all the necessary materials. These are always available at local hardware stores so they can be owned for a period of time. You need to figure out the necessary amount of drywall. It’s best to use twelve foot sheets of paper, because sometimes it’s cheaper to buy and you have fewer sheets to contend with. The thickness of the drywall must also be determined. Usually in residential areas you go to use standard inch drywall. If the ceiling trusses are in 24 inches 5/8 thick sheets should be used, say 1/2 inch sheets over time. If you use the area to bend the curve you need to use the best thickness. Commercial jobs generally use 5/8 inch for durability. Any area exposed to moisture (such as a bathroom) needs what is known as green and hardwood flooring. Green board is used in a place that is exposed to a lot of moisture. Green board moisture resistant, not moisture proof! Hard rock in the barrel area (in wet areas).
You should also count on the supply of drywall screws, one box of screws will cover a little over 150 sheets of drywall. When buying screws, let the operator know what the thickness of the board is and what kind of bolts they use. Metal studs require a “grabber” screw and the thicker the drywall, the longer the screw. Drywall tape comes in 250ft and 500ft rolls and a bucket of clay is needed for every 10 sheets of drywall. Whether you buy the materials at once or over time, there are some tips and tricks you should know about hanging and finishing drywall. Drywall designs create an optical illusion.
The first thing you will hang in the room will be the ceiling. The lines on your ceiling at twelve, twenty-four, and thirty-six inches will be where the screws fall into the ceiling. You need to note where any boxes or lights go so you can cut them out. Once you have chosen the area to start with, you need to measure the ceiling. If there is not twelve feet on the center of the ceiling truss, it is necessary to measure one of the trusses at dead center. You will use more screws in the ceilings than in the walls. When hanging on sheet rock you will put screws all around the edges to secure it (except for the cut end, which the other sheet of drywall is against for it on the second panel but when it is up, you divide the screws equally and in the seam, so that the two edges are joined, you connect 7 screws equally spaced “https://e-info.vn/tag/wall-hangings”>wall hangings on a drywall wall.
The first thing you need to do is mark some chalk bubbles on the floor and mark where some of the boxes will be. You will start left and move right and move from top to bottom. Before you put any screws in the box you need to have an area of drywall cut out of it so it doesn’t break the board. If it is already hooked into an electrical structure, make sure that the power is completely cut off.
Travel is the best tool to use and make the job a lot easier and faster. If you don’t know how to use it, take a piece of drywall and hold it against the box that is to be cut out and practice. Once it is felt that the path of the journey around the box will lead to the cutting. The trick is to remember that if you cut the area when traveling from outside, it will be counter-clockwise. If you cut from the inside of the box, you run clockwise.
The process of hanging drywall on the walls is almost the same as on the ceiling, but there are some tips and tricks that a person should know before undertaking this task. . The screw pattern on the wall will fall to sixteen and thirty-two inches plus the screw on the perimeter of the board. Setting the lines to these measurements make it much easier to place the screws in the boards.
A board is easy to cut and can be moved by one. With a 5’2″, 130lb board I was able to easily cut the board and move the board myself. The thing is not to fight with the board. Make sure there are no gaps when you hang it against another board. (You can shave the edges all the way down to that). it’s either higher than the others and you’ll just put all your screws in it. You need to screw it up against the sinker. You can screw up all the tools you have. An awkward angle make sure there are none.
The result is a lot more news than hanging. Make sure you machine all the flats (joints) and corners. Just wipe the slime over any nails that are not in these areas. Repeat this process two or three times over a period of days. Allow the clay to dry completely before adding another coat. You can see the flats if you also hold a line of drywall knife against the joint. This way you can tell if more mud is needed or if it needs to be sanded. The best thing to remember about drying is that the less mud the better.
Hanging and finishing drywall can be a tough job, but with the right knowledge it can save you a lot of money and be very rewarding for the work you did yourself.
