A ceramic tile floor with careful design – a brilliantly conceived concept, a carefully designed look and feel, and perfect ceramic tiles – can still be nothing if your tile installation isn’t performed correctly. Learn how to install your tiles the right way with these easy ceramic instructables, and watch your dream tile floor appear like magic.
1. Measure the length and width the area of the tiles will be, estimate how the number of ceramic tiles, the amount of thin stock, or cement, grout , and tools that need to be purchased (or rented). Start by measuring by finding the center point of the floor area you will be working on. You can do this by measuring the distance and marking the center. Do this in the opposite direction, and pay close attention to the center. The intersection of the two lines is the center of the area you will tile over. A chalk line is run over the intersecting lines. These chalk lines will help you later with the placement of the brick.
2. Having the right tools for the job is a must. You can buy most tools and materials at your neighborhood hardware store, or home center. For equipment that is over budget like your tile layer, try asking your local home appliance center or rental office if they have the equipment you need.
3. Make the floor (or, the area you will be covering) clear of debris, and smooth and safe. If we are working on a concrete subfloor, check for cracks and debris. First clean your concrete subfloor and repair the cracks. If you find that any cracks are too large to repair, replace those sections of the pavement with new concrete. Large cracks (or even smaller ones) expand over time and this also affects your tiles. If you are working with a plywood subfloor, make sure that the structure is durable and suitable to support your ceramic installation. Your plywood floor has to be at least 1/8″ thick, and supported by an equally strong substrate underneath. Ceramic tiles are heavy and need a subfloor that can support the combined weight. Otherwise, they will warp or even break. . If the existing ceramic tile you are working, all you need to do is use a large flat chisel and an inhaling hammer, and immediately remove the hammer. Glasses and long-sleeved work clothes.
4. Make a dry run of how you want your ceramic tile to look like. Remember your chalk? Lay the ceramic tiles following the chalk made earlier. Start in the center and work your way to the edges. Start at the center, where your intersecting lines meet and work out your path. You can go creative to install this piece of ceramic tile installation and actually see your wish come true.
5. Once you’ve seen how the tile design looks, you’re ready to start your floor! Place the middle tile and fasten it under your floor using a thin layer of cement, or the tile adhesive of your choice. It is recommended that you use a blunt trowel to apply the mortar under the floor, but you can also use a more common variety of trowels, which can be used for many ceramic tile installations instructions. To secure the ceramic in its place, press it while twisting it back and forth until the tile is not attached. If any mortar or grout leaks, use your trowel to scrape off the excess.
6. After installing your ceramic tiles, allow your floor to cure overnight. You can also check the tile or ceramic adhesive installation instructions for setting or hardening time.
7. Once you’ve laid your tiles, it’s time to lay the grout. Tiling grout is a device used to connect the tiles, fill the voids and seal the spaces between the tiles. The dye comes in a wide variety of colors to match your complexion and complexion. Mix the grout according to its ceramic tile package installation instructions. then put a floating grout ball into the frame. Use grout to float the corner so that you can fill as much grout as possible into the joint crack.
8. After placing the grout between the tiles, use a damp sponge to wipe off the excess grout. I wash the sponge often, so that only too much of the grout is taken up, and it cleans every tile. You have the option of applying sealant to the grout lines lines when they dry.
You have finally made your ceramic tile-flooring dream come true with these basic ceramic tile installation! Now all you have to do is keep your new ceramic tile keeping the floor clean and hygienic. And remember: New ceramic tile floors will be approximately 1/2″ taller, so you’ll need to fit your furniture, electrical outlets, and other fixtures.
