If you have found this article because you are trying to install a Kohler k-8030 or k-8031 rain panel, let me first warn you that despite appearances, it is not reasonable to install this replacement kit.
The parts are complicated, the instructions are terrible, and when you search the Internet for Kohler rain tile products, it’s common to see professional lead wires with statements like “I walked in… the homeowner said he wanted to have one. I’ll find another one…” and “… World and I was sober 20 years before I tried to install Kohler rain tiles” .
Have hope. I did, and I’m not a plumber. I am not an amateur plumber.
The first step is to build a rain gutter using the steel jig that comes with the rain tile kit. If you are not an expert in air sweat pipes, don’t even try this one. You will find a small creative joint acquisition, too (but not the 70 type of creative joint acquisition, you need to clear this head); There are two things that are relevant in editing that are simply not shown.
I know, I checked every Home Depot, Lowes, and professional plumbing supply in the Dallas/Fort Worth Metroplex and not. one is always a 1/2 inch copper four way fitting as shown in the drawing. Substitute enough parts to evenly distribute multiples; Just take the drawing with you and someone in the lead store will help you figure out the guests to buy.
Either jig/template to the pro and return them to build, or do what I did: Put the log and parts on your brother with a few tubes of that fresh air mowed epoxy and have him build while you pretend. to do other work, such as rough-in. Epoxy holds great (pressure tested since that day) and it’s the only way for an inexperienced plumber to get all those connections tight without squealing.
Once you’ve built your multiple shot, make sure you’ve made it as rough as possible on the rain tile. institution. If you don’t rough-in what you think install Kohler tile rain in a pre-existing shower, then your money take it and go buy a huge rain effect head shower instead, you have no hope of a decent rain tile panel without tearing up the ceiling and starting from a fresh molding (remember, suicide is a permanent solution; time is a problem).
The dimensions of the instructions do not leave you much room for error, and they are correct. This crazy thing has to fit into some very tight tolerances.
Comes with three different size 1 1/2 inch brass NPT nipples. Four each 1 ounce, 1-1/2 ounce, 2 ounce. Even if you make a rough to perfect plan, you still object to the thickness of the ceiling. tiles and thin mortar. You must resign yourself to trial and error… This is not the place for type of Personality, and admitting that this is not possible to progress perfectly in any place from here except first to health.
Click on the nipple eye lengths and measurements in the instructions, then choose which of the three lengths you think will fit your installation best. Do not put teflon tape or composite threads on your nipples yet. You have less than a one in a million chance of a perfect outcome. i did math
Screw the nipples into the manifold you (or your brother) built, then place the chromed plastic panel over them. It should be tight enough over the nipples to hang there.
Now develop one of the four rain tiles. Allen needs to twist the small screws on one edge of the chrome plate. Tighten those screws in (clockwise) to release the chrome face plate. Yes, I said “in”. This is a crazy thing, but they did it so that the screws were twisted on the edge of the plate. I guess it saves you the ability to fly too far and drop, … in which case they will be lost forever since they are almost microscopic.
Carefully cut off the gray crust of the silicon film and deposit it with a chrome plate. Below this you will see two hollow brass screws. They don’t look like an ANISOCYCLE, but a larger Allen key fits them and they twist counter-clockwise. Once the black plastic body separates from the copper water unit.
Take the Phillips head of the screw that holds the brass unit together and pull out half of the screw on the nipple. Use the wrench and adapter provided to tighten the socket to the copper unit and the nipple on the manifold. If the screws are tight against the plastic cup on the board, start with the other length of nipple.
Once all four are secured each housing of the second halves of brass (pay attention to mark the edge and take care of the lines with the double tab in each plastic housing) and secure them snugly with screws; after you’ve hunted everywhere in the floor, the workshop, and the floor because you can’t remember where you put them, but you finally found them in where you recently found out according to proplumb203 in the pipe and fitting market no one has ever successfully installed a Kohler rain tile.
If the board pulls snugly against the ceiling just enough to slightly compress the black foam gasket, congratulations, you can take everything apart and repeat the process after applying Teflon tape or thread compound to seal each side of all the nipples.
Next, attach each black plastic plate, then carefully press the edges of each gray silicon membrane back into place. Finally, place the chrome plated hooks without any holes on the edge of the black plastic plate and turning with the smallest Allen screws to secure them. Watch carefully and make sure you stop turning the set screws once they are flush with the surface of the rim of the chrome plate.
The installation must be complete and all four tiles must fit together without the slightest touch.
